Due to its unique formula, PVC doors and windows have good corrosion resistance, and the use of plastic steel doors and windows than the use of wooden doors in winter room temperature can be higher 4-5 degrees, and now most people choose this plastic doors and windows. U-PVC steel doors and windows are a new type of chemical building materials. They are the fourth generation of energy-saving doors and windows following wooden doors and windows, steel doors and windows, and aluminum doors and windows. They are high-quality energy-saving products recommended by the Ministry of Construction. Plastic steel doors and windows are made of plastic profiles through cutting, fitted with reinforced steel after welding, and then fitted with seals, wool, hardware and other accessories made. Because of its beautiful appearance, strong corrosion resistance, good water and heat insulation, and easy maintenance, it is increasingly favored by people. In recent years, the momentum of development has been extremely rapid, but too rapid development can easily lead people to ignore many hidden issues. And the market is mixed, what quality levels are there, the average customer does not know enough about their performance, there is no detection tool, and they are not familiar with their performance, especially in the case of how to identify the quality of steel doors and windows without the control of the purchase, Sometimes it is hard to be deceived. Dikai Windows and Sun Rooms one. Profile quality of steel doors and windows The appearance of the profile should be observed. The color should be blue-white, not white, which is usually considered by people. Pay attention to whether the color of the frame and the fan profile of the door and window is consistent, whether the appearance is uniform and whether the cavity distribution is reasonable. In the formulation of steel door and window profiles, calcium carbonate is usually added as the filler material, and some manufacturers reduce the cost. If the amount is too much, it becomes a calcified plastic. The surface of doors and windows made of this plastic lacks luster and is slightly rough. Hard and brittle, it looks like a rough feeling like stones, normal steel doors and windows, the surface is usually shiny, very tough. two. Door and window gaps and seals Look at the tightness of the fit between the various profiles, whether the incision is flush with the fit, the height of the profile overlap, and so on. General steel doors, the main part of consideration is the door frame, the gap between the fan, the door trim and the door edge, the various sections of the shutter connection, seals, etc.; if assembled door panel, but also consider the door Gap; is to open the door but also whether the two doors closed after the light and so on. Similarly for the use of plastic steel windows, in addition to the assembly of a variety of profile assembly clearance to be considered, the sealing strip is uniform and solid is also very important, the interface gap should not exceed 1mm, which reflects the window sealing performance. Plastic-steel doors usually do the inner door of a building, and the sealing requirements are not so high. Various clearance values ​​are stipulated in national standards, but for customers, the smaller the gap value at various profile connections, the tighter the fit and the more exquisite the assembly process, which reflects the assembly level and the accuracy of the assembly tools. three. Welding of steel doors and windows To see if the weld is flush, whether there are cracks, and whether the internal and external corner seams are clean and beautiful, use a box ruler to measure the diagonal size of the steel doors and windows, the diagonal size difference should be no more than 3mm, diagonal difference The smaller the display process, the finer it will be for installation. four. Plastic steel doors and windows hardware The quality of hardware has a certain influence on the life of doors and windows. The hardware used should look thick, and the surface gloss is better, the protective layer is denser, and there is no scratching phenomenon. The most important point is that the opening should be flexible. Fives. Reinforced steel for steel doors and windows According to national standards, there are different requirements for the wind pressure resistance of plastic steel doors and windows. The frame of plastic steel doors and windows and the inner cavity of the fan shall be equipped with reinforced steel. According to the height, there are three types of reinforced steel of 1.2mm, 1.5mm and 2.0mm to ensure the The product's ruggedness and longevity. In order to reduce costs, some manufacturers do not install or load reinforced steel that does not meet the requirements. Customers should pay special attention when purchasing products. The usual inspection methods are: 1. The reference weight method estimates that the weight of the door and window is the nickname, and the weight of the door and window with reinforced steel is heavy, and vice versa. 2. Use a magnet to place the frame and fan on the door and window. If the magnet is adsorbed, there will be reinforced steel in the profile, and vice versa. 3. Observe the frame of the door and window, whether there are screws fastening the steel on the fan, it can also prove whether there is reinforced steel. In short, customers should be cautious when choosing products, try to use regular manufacturers' products, and strictly inspect them so as not to be deceived. Doors Doors and Windows Hardware Windows Doors Shutters Shutters Floor Drain Cover,6 Inches Floor Cover,Bathroom Floor Drain Cover,Anti-Odor Square Floor Drain Cover Kaiping City Jinqiang Hardware Products Co.,Ltd , https://www.jmkimpowerdrain.com
Ship windows and sun room 
Creation of doors and windows and sun room