Industrial control motherboard common fault repair: Common fault one: no display at boot There is no display when the computer is turned on. First of all, we have to check the BIOS. The BIOS of the motherboard stores important hardware data. At the same time, the BIOS is also a relatively vulnerable part of the motherboard. It is extremely vulnerable to damage. Once damaged, the system will not run. This type of failure is usually caused by the destruction of the motherboard BIOS by the CIH virus. (Of course, it does not rule out that the motherboard itself is faulty and the system cannot run). Generally, the data in the hard disk will be completely lost after the BIOS is destroyed by the virus. Therefore, we can judge whether the BIOS is damaged by detecting whether the data of the hard disk is intact. If the data of the hard disk is intact, there are three reasons why the booting is not displayed: 1. Because there is a problem with the motherboard expansion slot or expansion card, the motherboard does not respond and has no display after plugging in an expansion card such as a sound card. 2. The jumper-free motherboard has a wrong CPU frequency set in CMOS, which may cause no display failure. For this, just clear CMOS to solve it. Clear the CMOS jumper is generally near the lithium battery of the motherboard, its default position is generally 1, 2 short circuit, as long as it is changed to 2, 3 short circuit for a few seconds to solve the problem, for the old motherboard if the user can not find To the jumper, just remove the battery, wait until the boot display enters the CMOS settings, then turn it off, and the battery will also go up to the CMOS discharge. 3. If the motherboard does not recognize the memory, the memory is damaged, or the memory does not match, it will cause the display to fail without booting. Some old motherboards are more picky memory. Once plugged in memory that the motherboard does not recognize, the motherboard will not boot, and even some motherboards will not give you any fault prompts (tweets). Of course, sometimes in order to expand the memory to improve system performance, the result is that plugging in different brands and types of memory will also lead to such failures, so you should pay more attention when overhauling. For the failure of the motherboard BIOS to be destroyed, we can plug in the ISA graphics card to see if there is any display (if prompted, you can follow the prompt steps.) If there is no boot screen, you can make a floppy disk that automatically updates the BIOS. Re-flash the BIOS, but some motherboard BIOS is destroyed, the floppy drive does not work at all, at this time, you can try to solve it with hot plug method (I have tried, as long as the BIOS is the same, can be successful in the same level of the motherboard Burn.). However, the use of hot-swap in addition to the need for the same BIOS may cause damage to some components of the motherboard, so a reliable method is to use the code writer to write the BIOS update file to the BIOS. Common fault 2: CMOS settings cannot be saved This type of fault is generally caused by insufficient battery voltage on the motherboard. This can be replaced, but some motherboards can not solve the problem after replacing the battery. There are two possibilities: 1. The motherboard circuit problem, looking for professional repair; 2. The motherboard CMOS jumper problem, sometimes because the wrong CMOS jumper on the motherboard is set to clear option, or set to an external battery, so that CMOS data can not be saved. Common fault 3: After the motherboard driver is installed under Windows, the crash occurs or the speed of the optical drive is slow. This phenomenon sometimes occurs on some brand-name motherboards. After the motherboard driver is installed, restarting the computer cannot enter the Windows 98 desktop in normal mode, and the driver cannot be uninstalled under Windows 98. If this happens, it is recommended to find the latest driver reinstallation, the problem can generally be solved, if it is not, you can only reinstall the system. Common fault four: the mouse is not available when installing Windows or starting Windows The software cause of such a failure is generally caused by a CMOS setup error. There is a modem use IRQ project in the power management bar of the CMOS settings. His options are 3, 4, 5, ..., NA. Generally, its default option is 3, and it is set to an interrupt other than 3. Just fine. Common fault five: the computer crashes frequently, and there will be a crash when performing CMOS settings. There is a crash in CMOS. Generally, there is a problem with the motherboard or the CPU. If the fault cannot be solved by pressing the method, then only the motherboard or the CPU is replaced. The occurrence of such a fault is generally caused by a problem with the motherboard Cache or poor heat dissipation of the motherboard design. The author found on the 815EP motherboard that the fault caused by the heat dissipation of the motherboard is not good enough. After the crash, touch the motherboard components around the CPU and find that the temperature is very hot. After replacing the high power fan, the crash is resolved. For problems with Cache problems, we can enter the CMOS settings, the Cache can be banned to solve the problem smoothly, of course, the speed will be affected after the Cache is banned. Common fault six: motherboard COM port or parallel port, IDE port failure Such failures are generally caused by the user plugging and unplugging the relevant hardware. At this time, the user can replace the multi-function card, but before the replacement, the COM port and the parallel port must be disabled on the motherboard (some motherboards have IDE ports). To prohibit the normal use) Concerned about surprises Label: Industrial computer repair motherboard common fault repair Previous: Ozone disinfection cabinet usage Next: Hydraulic system according to standard commissioning and maintenance
Dimethyl Malonate is a common organic reagents, dimethyl malonate is an important raw material for the production of pharmaceutical pipemidic acid. Foreign dimethyl malonate is mainly used as non-ethoxymethylene process production of pipaic acid raw materials, and orthoformate and urea reaction production of pipemidic acid
Monopotassium Phosphate in the application of detection and production applications play an important role
Organic Intermediate,Inorganic Salt,Dimethyl Malonate,Monopotassium Phosphate,Phosphate SJZ Chenghui chemical co ltd , https://www.chenghuichemicals.com