How about the assembly process of cabinet cabinets? Hot Rolled Stainless Steel Sheets
The whole kitchen cabinets in modern kitchens are generally on-site production and processing. Generally, there are three major components such as cabinets, wall cabinets, cabinet countertops, etc., and the cabinets need to pay attention to more matters during construction because it Need to consider its load-bearing factors, how about the cabinet cabinet assembly process? Xiaobian suggested that you still have to pay attention to the cabinet cabinet installation steps and skills to analyze and consider.
The assembly steps of cabinet cabinets mainly include:
1. According to the installation position of the fan, determine the hardware model and the direction of the split fan. Generally, the right fan in the opening direction should be used as the cover fan.
2. Check the size of the frame: the height of the frame should be measured at both ends; the width of the frame should be at the top, middle and bottom of the frame, and the corresponding part of the fan should be marked.
3. According to the scribing, the frame fan will be trimmed for the first time, so that the frame and the fan are suitable for the seam. The test and the second planing line are prepared. At the same time, the position of the frame and the fan hinge groove is drawn, and the scribing is avoided. Raise your head up and down.
4, shovel, picking page slot installation hinge: According to the hinge position of the mark, use the flat shovel to cut out the hinge edge, you can pick up the page slot.
5. Installation: When installing, the hinge should be pressed into the hinge slot of the fan first, and the fixing screw should be tightened. The depth of the groove should be adjusted during the trial installation. Adjust the gap of the frame fan and each hinge on the frame. Screw one screw first, then close it. The inspection frame and the fan are flat and free of defects. After meeting the requirements, tighten all the screws. Wood screws should be nailed into the full length 1/3, screwed into 2/3. If the frame or fan is yellow bud or other hardwood, the hinge mounting screws should be positioned and the hole diameter is 0.9 times the diameter of the wood screw, and the depth of the eye is 2/3 length of the screw.
6. Install the split fan: firstly measure the size of the frame and the fan, determine the middle seam and the depth of the cut, and plan the groove after the line. When the test is suitable, install the left fan first and then install the cover fan.
Since the installation requirements of the cabinet ceiling are very professional, it is recommended that the owner choose the cabinet company with good reputation and brand strength to purchase the products. They usually have a professional technical team to provide on-site installation services to ensure your home. Cabinet cabinet installation quality.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Stainless steel plate surface smooth, high plasticity, toughness and mechanical strength, acid, alkaline gas, solution and other media corrosion resistance. It is an alloy steel that does not rust easily, but not absolutely. Stainless steel plate refers to the corrosion resistance of weak medium such as atmosphere, steam and water steel plate, and acid resistant steel plate refers to the corrosion resistance of chemical etched medium such as acid, alkali, salt steel plate.
According to the structure is divided into austenitic stainless steel plate, martensitic stainless steel plate (including precipitation hardening stainless steel plate), ferritic stainless steel plate, and austenitic ferritic biphase stainless steel plate and so on four categories? According to the main chemical composition of the steel plate or some characteristic elements in the steel plate to be classified into chromium stainless steel plate, chromium nickel stainless steel plate, chromium nickel molybdenum stainless steel plate and low carbon stainless steel plate, high molybdenum stainless steel plate, high purity stainless steel plate. According to the performance characteristics and use of steel plate classification, is divided into nitric acid resistant stainless steel plate, sulfuric acid resistant stainless steel plate, pitting stainless steel plate, stress corrosion resistant stainless steel plate, high strength stainless steel plate. According to the functional characteristics of the steel plate, it is divided into low temperature stainless steel plate, no magnetic stainless steel plate, easy cutting stainless steel plate, super plastic stainless steel plate. Currently, the commonly used classification method is according to the structural characteristics of steel plate and steel plate chemical composition characteristics and the combination of the two methods. Generally divided into martensitic stainless steel plate, ferritic stainless steel plate, austenitic stainless steel plate, duplex stainless steel plate and precipitation hardening type stainless steel plate or divided into chromium stainless steel plate and nickel stainless steel plate two categories.
Typical uses: pulp and paper equipment heat exchanger, mechanical equipment, dyeing equipment, film washing equipment, pipelines, coastal area building external materials, etc.
Hot Rolled Stainless Steel Sheets,Stainless Steel Plates Sheets,304 Stainless Steel Sheet,Aisi Stainless Steel Sheet
Shandong Xinsuju Steel Co.,Ltd. , https://www.sawlpipe.com