4x4 Winch is a kind of winch which is
powered by direct current electricity provided by the vehicle's electrical
system and pull the vehicles out of trouble through the cable or synthetic
ropes. It is typically mounted to a vehicle's front or rear bumper. Winch electric
is one of the necessary tools for off road adventure.
8000LBS Line Speed And Amp Draw(First
Layer)
8000LBS Line Speed And Amp Draw(First Layer)
Line Pull
lb
No
4000
6000
8000
kg
LOAD
1812
2718
3624
Line Speed
ft/min
33.59
20.93
14.33
10.76
m/min
10.24
6.38
4.37
3.28
Motor Current
Amps
72
200
250
300
8000LBS Line Speed And Amp Draw(First Layer)
Layer of Cable
1
2
3
4
Rated Line Pull per Layer
lb
8000
6000
4000
3000
kg
3636
2727
1818
1364
Length of Cable on Drum
ft
11.28
23.94
38.00
45.92
m
3.438
7.3
11.586
14
Typical Applications: off-road vehicles, agricultural vehicles, ATV all-terrain vehicles,
yachts, fire rescue vehicles, road barrier vehicles and other special vehicles,
special vehicles.
Usages:
Put on a pair of thick gloves. Never handle a winch cable without gloves on. The cable
could cut your hands.
If the
winch cable doesn't reach the anchor, look for another anchor that's closer to
your vehicle.
Wrap a tree trunk protector around the bottom of the anchor. A tree trunk protector is a thick nylon strap with two loops, one on
each end. Wrap the protector around the anchor so the two end loops are facing
you. Hold the two end loops in your hand.
If your
winch didn`t come with a tree trunk protector, you can order one online or find
one at your local hardware store.
Hook a D-shackle through the 2 loops on the
protector. A D-shackle is a curved shackle with a large
pin that screws in and out of the shackle. Remove the pin from the D-shackle
and put the curved part of the D-shackle through both of the loops on the tree
trunk protector. Once the loops are on the shackle, reinsert the pin and twist
it to tighten it into place.
Turn the disengage lever back to [engaged." You want the lever to be back in the position it started in
before you released the winch cable. This will prevent more cable from coming
out of the winch.
Use the winch remote to slowly pull the winch
cable taut. Press the button on the remote control to
start pulling the winch cable back into the winch. This will cause the winch
cable to tighten. Stop pressing the button when the cable is taut
Our Services
1. OEM service is available.
2. Fast producing time.
3. Inspect products one by one before
shipping
4. Cheapest price for electric and hydraulic
winches
5. Reply promptly in 24 hours.
If you have any questions, please contact
with us directly. Compass winches are produced by With High Quality and Good
Appearance. Welcome you can visit our Factory. For inquiry, please directly send
mail to us.
electric mini winch, mini electric winch, electric winches for boats Suzhou DAO Material Technologies Co.,Ltd , https://www.dao-compass.com
Plug the winch remote control into the winch. Your
winch should have come with a remote control attached to a long cord. Look for
the plug at the end of the cord and attach it to the corresponding receptacle
on the outside of the winch. Run the remote control cord from the winch to the
driver`s seat and place the remote control in your vehicle
Find something in front of your car to anchor your winch to. A large tree trunk, boulder, or other vehicle is ideal.
Don`t anchor your winch to something small and weak or you risk breaking it.
Try to find an anchor that`s straight in front of your vehicle.
Use the disengage lever to release the winch cable. The disengage lever should be located on the outside of
the winch. The lever should have an option that says [free spool" or
[disengaged." Turn the lever to that option. This will release the cable so
you`re able to manually pull it out from the winch.
Pull the winch cable all the way to the anchor. Don't pull too
much of the cable out or you'll create unnecessary slack. Set the end of the
cable down next to the anchor.
Hook the winch hook to the D-shackle with the tip facing up. The winch hook is the hook at the end of the winch cable
ZJ Roots vacuum pump maintenance skills (a)
ZJ Roots vacuum pump in the usual course of how to maintain it? Believe that with Roots vacuum pump are very concerned about this issue, Zhejiang Vacuum Pump Factory concluded by the following maintenance methods and experience for your reference; 1, always check the oil level position, do not meet the requirements to be adjusted to meet the requirements. ZJ Roots vacuum pump operation, the oil level to the center of the oil standard. 2, the oil change period according to the actual conditions of use and can meet the performance requirements and other considerations, by the user discretion. General new ZJ Roots vacuum pump, pumping clean and dry gas, it is recommended to change the oil about 100 hours time. Oil to be seen after the black metal powder, the oil may be extended after the expiration date. 3, regular inspection of oil quality, oil deterioration should be found in a timely manner to replace the new oil, to ensure that ZJ Roots vacuum pump is working properly. 4, under normal circumstances, ZJ Roots vacuum pump should work after 2000 hours of maintenance, check the aging degree of plastic seal, check the exhaust valve is cracking, cleaning the valve plate and the exhaust valve seat on the dirt. Clean the entire ZJ Roots vacuum pump cavity cavity parts, such as rotor, rotary blade, spring and so on. General use of gasoline cleaning, and drying. After cleaning the rubber parts with a dry cloth can be dry. When cleaning the assembly should be carefully handled and bruised. 5, add bearing lubricating oil to the bearing body, observe the oil level should be at the center line of the oil standard, the lubricating oil should be replaced or replenished in time. 6, Check the Roots ZJ-type vacuum pumps and joints with loose lines. Rotate the ZJ Roots vacuum pump by hand and see if the ZJ Roots vacuum pump is flexible. 7, reassembly should be carried out after the trial run, the general shall be empty for 2 hours and change the oil twice, due to cleaning in the ZJ Roots vacuum pump will leave a certain amount of volatile, to be functioning properly, then put into normal work. 8, start the motor, when the ZJ Roots vacuum pump normal operation, open the export pressure gauge and imported ZJ Roots vacuum pump, depending on the pressure showed its appropriate, and gradually open the gate valve, while checking the motor load conditions. Zhejiang vacuum pump plant related articles Read: Rotary vane vacuum pump fault diagnosis and solutions (a) Rotary vane vacuum pump fault diagnosis and solution (b) of the nine categories of vacuum pumps expert Weaponry: How to maintain the vacuum pump Roots vacuum pump With eight characteristics of the vacuum pump industry standards (a) of the vacuum pump industry standards (b) of the cause of the corrosion of the vacuum pump and the solution Vacuum pump selection Vacuum equipment maintenance and repair Copyright ZZ Roots vacuum pump (a) articles Must be noted in the form of links between the author and the original source Zhejiang Vacuum Pump Factory.