Nowadays, people pay more and more attention to the sanitary ware bathroom, mainly because of the continuous improvement of living standards, not only paying attention to the function of the bathroom, but also requiring beauty. However, the bathroom renovation is the most complicated part of the overall home improvement. For many people, it is not very clear about the installation of sanitary ware. Then, the next small series for everyone to introduce sanitary ware bathroom installation steps. Sanitary ware installation steps 1, the installation of the bathtub The first step: the need to test the water, to see if there is a leakage phenomenon: we need to install the appropriate water accessories before installing the bathtub, and need to do a 24-hour closed water, and then look at the leaking of the bathtub In particular, pay attention to the overflow. The second step is to level the bathtub. When we set up the bathtub, we must pay attention to the corresponding water outlet is lower than the end of the inlet, which will avoid the poor sewage. Corresponding bathtubs must not only be visually level, but also care must not affect drainage. The third step is to fill sand. Compared with cast iron bathtubs, it is strong but its thermal conductivity is very fast. Therefore, it is necessary to use Zhonghe sand for compacting. Of course, foam can also be used because the foam does not have liquidity. When filling river sand, it is also necessary to note that sand cannot leak into the sewers. Step 4: Leave the access port. When installing, we also need to pay attention to the 300mm wide and 400mm holes in the place where the drain is located, and carry out waterproof and antiseptic treatment according to the size. The purpose of this is to have a good mouth when we are doing maintenance. 2, toilet installation The first step: we need to remove the pipe plug from the ground, and then we need to check if there is any debris in the pipe, otherwise we need to remove the corresponding debris. Then clean the area around the nozzle, and then connect the corresponding outlet pipe of the toilet with the outlet pipe to make it flat and correct. Then we need to mark the bolt holes in the toilet bowl. Step 2: Make a hole. A hole with a diameter of 20 mm and a depth of 60 mm should be drilled at the corresponding mark. Then insert the bolt into the hole, then cement it firmly and align the toilet eye with the bolt. Then put the putty around the corresponding outlet of the toilet bowl and the outlet nozzle, and screw the corresponding four bolt holes of the toilet until the elasticity is moderate. The third step: install the rear center of the toilet. According to the corresponding drawings or the scribed section for installation, and the relevant bolts need to be fixed, the degree of fixing needs to be moderate, not too tight. Step 4: Install the back tank. When installing the back tank, we need to pay attention to the proper size, not too loose or too tight. Step 5: Connect to water. The installation of the Sheung Shui system also needs attention, and it cannot leak water. When you finish the water, you need to pay attention to moderate elasticity. 3, washbasin installation The first step is to install the washbasin: When we are installing the washbasin, we must first draw the line of the discharge pipe, and then measure the height of the floor upwards, and draw a horizontal line on the wall. Mark the mark according to the width of the basin, then make a 120 mm deep hole. Clean up the related debris and keep it clean. The second step is the installation of the cast iron washbasin. As with the above installation method, it is also necessary to mark the center of the discharge nozzle, then measure the height, and draw horizontal lines to form a crosshair. Depending on the width of the washbasin, mark it on the centerline, and place the pots in place, leaving the screw holes in place, and the size must be marked. Sanitary Ware Buying Tips A look: Consumers can choose to look closely at the reflection of high-end sanitary ware products from the side under strong light. There is no or little trachoma and pitting on the surface. Products with a high brightness index use high-quality glazed materials and a very good glazing process. They have good reflectivity to light and thus have good visual effects. Second touch: You can use the hand to gently rub on the surface, it feels very smooth and delicate as well. You can also touch the back and feel that there is a fine feeling of "rustle". Three Listening: You can use the hand to strike the surface of the ceramic. The sound of a good ceramic material is relatively crisp. Four: The main reason is to examine the water absorption rate. The lower the water absorption, the better. Ceramic products have a certain adsorption and penetration ability for water. If water is sucked into the ceramic, it will have a certain degree of expansion, which will easily cause the glaze on the ceramic surface to crack due to expansion. Especially for toilets, if the water absorption rate is high, dirt and odor in the water can be easily absorbed into the ceramic, and unpleasant odors will be produced over time. Editor's summary: The sanitary ware installation steps are introduced here, and I hope to help everyone. If you want to know more about yourself, you can follow the information on this site. Sanitary Ware Sanitary Ware Bathroom Installation Ammonium Sulfate is widely used as food ingreident, nutritional supplement in fermentation, pharmaceutical, feed ingredient or analytical reagent. High purity Ammonium Sulfate is produced by Ammonia and sulphuric acid. Kolod is a leading supplier of high purity Ammonium sulfate in China. Ammonium Sulfate Ammonium Sulfate Food Grade, Ammonium Sulfate Feed Ingredient, Ammonium Sulfate Pharmaceutical Grade Jiangsu Kolod Food Ingredients Co., Ltd. , https://www.kolodchem.com
