Furniture Handle,Exterior Door Handle,Nordic Brushed Gold Handle,Space Aluminum Alloy Handle Guangzhou Junpai Hardware Co., Ltd , https://www.gdjhfurniture.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>How to properly use and protect wheat combine harvester How to properly use and protect the wheat combine harvester
The annual "Three Summers" busy season will begin; in order to better ensure the three summer wheat harvest operations are carried out in a rational manner; the current analysis of the application of wheat combine harvester protection is as follows: /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
First, the view before the use of the combine harvester:
ã„’å”¬â”˜è§³æ¦ é’ é’ é’ é’ é’ é’ é’ å‹Ÿ å‹Ÿ å‹Ÿ å‹Ÿ å‹Ÿ ç—ªå’›è¿¥è°Œè© é’ é’ é’ é’ é’ é’ é’ é’ é’
2. Can the three adjustments of the whole column and the alignment be qualified?
3, the gap of the blade cutter is fine.
When cutting, the cutter should be disconnected from the driving device; if one hand can pull the cutter gently, it is proved that the equipment adjustment is correct.
.ǘ┘觳橥蚜9é¾åŸ barrel and ç沧 dark annoyed
1, the rod (and nail teeth); the fixed condition of the concave plate and the drum assembly. To check the locking condition of each nut one by one.
2. Check whether the threshing gap (including the threshing gap of the nail roller) can be uniform. When viewing, the concave plate should be raised to the highest position; then change the roller; check whether the roller and the concave plate, the end surface of the roller and the side wall can have the scratching appearance Whether the change can be simple and sensitive.
3. Check the balance of the drum.
4. Verify that the indication readings of the threshing gap adjustment handles are common to the practice gap.
ㄈ┘觳楦骰刈幔 å²¢ å²¢ 沧 沧 沧 沧 沧 沧 沧 沧 沧 沧 沧 沧 å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„ å„Then change the reverse part by hand; if it can change gently, no impact, hang the surface; prove that the parts and bearing equipment are correct. Finally, hit the shaft head with a hammer; the shaft does not move; and has elasticity; The equipment with the inner ring of the bearing is tight.
1. The model of the pulleys between the sprocket wheels of the same transmission circuit should be in the same plane; the pulley shafts should be parallel. ; not skewed, the center of each sprocket in the same transmission circuit should be installed in the same plane; each sprocket shaft should be parallel; not skewed.
2. The pulley and sprocket are firmly on the shaft; the beating is small.
3. Check whether the orientation and gap of other adjacent components are correct.
ㄎ澹┘觳榱刺跗ã”慕舳
1. The tightness of the chain 2. The tightness of the belt. The bad èŸÇŽ èŸÇŽ èŸÇŽ ãƒ‹ç‚•è›Žã• ãƒ‹ç‚•è›Žã• æ¦ æ¦ æ¦ æŸ¥çœ‹ 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看 查看The tightening condition. Beijing 2. 5 and Spring Breeze 5 should pay attention to the riveting condition of the skewed conveyor plate; there must be no loose appearance.
2. Check the fastening condition of the top wire or the shaft end bolt and the shaft nut which are positioned on the shaft of each pulley and sprocket; to avoid the pulley and the sprocket from swimming during the operation; the rolling key or the detachment of the surface.
ㄆ撸┘觳榱蛹å‘浜锨æ¦The demand cooperation gap is suitable; avoid premature wear and damage.
It is necessary to have 80% of the teeth or corrugations of the main driven discs; the maximum gap of the teeth or corrugations that cannot be tightly combined shall not exceed 1 mm.
2. The tightness of the tension spring should be adjusted to the extent that the tension spring can be changed by one hand force. The sum of the gaps between the rings should ensure the sliding disc change (that is, the sum of the gaps between the turns of the spring should be larger than the teeth). high).
. Niu ┘觳楦é’ㄖ亓 Kang sodium sodium 馇æ¦é¾Š é’ã„“æ°²å›å¨´ é’ã„“æ°²å›å¨´ å« è° è° è° è° è° 1〠1〠1〠1〠1〠1.
2. Spring breeze 5 and Beijing 2. 5 should check the parallelism between the header and the ground.
ㄊ┘觳楦é«å“Ÿ èŠŠé¦‡æ¦ èŠŠé¦‡æ¦ èŠŠé¦‡æ¦ ã„Šå”¬â”˜è§³æ¥¦éž‘ ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 ㄊ唬┘觳楦鞑 榛钚 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 ㄊ┘觳楦 æ¦. ; the number is smooth; to prevent loss.
ㄊ┣R æ… å´ç½¨èƒª å´ç½¨èƒª å²·èž… å²·èž… å²·èž… è§³æ¦ è§³æ¦ è§³æ¦ è§³æ¦ 6 6 6 6 6 6 6 6 6 6 6
ã„Š â”³è©ˆè ¹è§³æ¦›é«‚è¯Ÿéž” â”³è©ˆè ¹è§³æ¦›é«‚è¯Ÿéž” 抟 抟 抟 抟 粑 粑 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 ㄊ澹┳懦 〠〠〠〠〠〠〠〠〠〠〠〠〠〠〠〠Trial operation: After the starter is started; the start is idling at a low speed of 600 800 rpm for 5 minutes; then gradually increasing to the extra speed. The initiator is at a low speed; the oil pressure is not lower than 0.5 kg/cm 2 for an additional speed. When the oil pressure should not be less than 1.5 kg / cm 2 . In the start of the machine operation; be careful to listen to the presence or absence of abnormal sound; look at the appearance of the reading; check the presence or absence of oil leakage in the local empty work to reach 10 15 minute.
2, some of the empty test operation of the threshing: adjust the gap of the drum to the maximum orientation; open the lower cover of each elevator; change the pulley of the central drive shaft by hand; make the whole machine change after the machine is turned. After the machine is viewed normally The starter can be started; when the speed reaches 600 800 rpm; the joint de-cold is somewhat. Then gradually increase the throttle to reach the normal test operation for 20 hours. At this moment; park every 20 minutes; check the bearing heat Condition; the fastening status of each department. Found faults; should be promptly removed.
3, walking some empty test operation; combine harvester walking empty work; should gradually improve the gear position from the beginning of a gear; punctual lifting and harvesting the harvesting platform and reel; pay attention to listening to some of the noise; see the gearbox with or without Oil spill and overheating appearance.
4, with load test operation: after 25 hours of walking some empty test after the test; the machine is normal; can carry out the load test operation. During the test run, the crops in the flat area are harvested without weeds and non-falling crops; when starting the test, the low speed should be used first. Gradually increase the load of the machine. After 15 hours of test drive; perform a full skill protection; remove the oil filter; replace the oil in the bottom of the engine oil; and follow the difficulties presented in the test run; make all adjustments; 3. The crew is put into the harvesting work under outstanding skill conditions.
Third, the use of combine harvester. ㄒ唬┨锛渥 㷠㷠㷠㷠㷠㷠㷠㷠㷠㷠㷠㷠㷠㷠收割 收割 收割 收割 收割 收割 收割 收割 收割
2, select the crew walking route; according to the crop topography; determine the harvesting plan.
3, eradicate the obstacles in the field; necessary to do a significant symbol.
4. Harvesting with a tractor-type combine harvester; cutting the sidewalk in advance; cutting the grain-discharging road for a long time.
Ǘ┦å´ç½¨é¥• 钡牟 stool child 1, the combine harvester 10 15 meters away from the crop to be cut; should smoothly engage the working clutch at low speed; make the working parts work, pull the operating valve to slow down the combine harvester; Reduce the harvesting table to the normal cutting height, then gradually increase the throttle; let the initiator harvest at the extra speed.
2, harvest 50 100 meters in the future; parking should check the quality of the work; if necessary, make appropriate adjustments. Then run 50 100 meters; then check the adjustment; until the quality of the work reaches the demand; then put it into normal operation.
3. After normal harvesting; the driver should adjust the height and speed of the reel, the height of the harvesting table and the traveling speed in time, pay attention to the investigation of the appearance and lighting signal equipment, listen to the sound of each working part; and find the abnormal appearance; Timely parking; find out the reason; remove the problem.
4. Normal harvesting; it is not allowed to reduce the travel speed by reducing the throttle; avoiding the formation of work quality degradation or blockage. At this moment, the hydraulic operated valve handle can be placed in the deceleration orientation; to reduce the travel speed of the machine.
5, after the operation of the obstruction. Should slow down the speed of travel; close to the obstruction; raise the harvesting station properly; skip the obstruction and drop the harvesting station; this process should not reduce the speed of the launching machine; A larger turning radius should be used.
6. Turning and harvesting operations. When turning and harvesting; should travel at low speed (but not reduce the throttle); avoid sharp turns; prevent overwhelming crops;
Fourth, pay attention to matters and safe operating procedures 1, start the machine to start, engage the clutch and walk before; it is necessary to announce the signal; to ensure the safety of the device and personal.
2. The driver should pay attention to the operation status and work quality of each component during the operation; find the problem and deal with it in time.
3. Depending on crop conditions, climate change and harvesting time; the relevant components and travel speed should be adjusted at any time to ensure the quality of the work.
4. When harvesting at the beginning of each plot; it should be operated at a low speed; for viewing and investigation; then gradually speed up.
5. During normal operation; do not touch the working parts by hand, and various adjustment and protection should be carried out after the start of the machine.
6. Before the header is not placed firmly on the support; stop the personnel from working under the header.
7, always look at the reliability of steering and braking tissue.
8. Stop using the harvester to tow other equipment.
9. When the operation is stopped; the shifting should be placed in the neutral position in time; do not leave the working clutch or the closed initiator.
5. The protection and protection of machinery and equipment is based on Beijing 2. 5 and Spring Breeze 5.
ㄒ唬┠2 2. 5 protection protection 1, daily skill protection. 1) Before the daily work, the residual dust, hull, awning, stem and other attachments on the machine should be arranged; the unique is the concave plate, The surface of the slab is swayed, the upper and lower screens of the grain clearing room, and the key surface of the drafter are cleaned.
.2) Check the cutter for damage and some fixed conditions; uniquely, check the fixing bolts and the cutter head bolts of the cutter head transmission organization.
.3) Check the fixing status of the parts on the reel.
.4) Check the tension of the chain of the skew feeding chamber; the middle part should be able to lift 20 30 mm by hand.
.5) Check the fixing condition of the roller bar concave plate and its bearing seat.
.6) View the fixing condition of the wood bearing bush and the crankshaft bearing seat of the drafter.
.7) View the partial pain bearing housing of the transmission grain cleaning chamber; the fixing condition of the lifting chamber housing of the grain cleaning chamber.
.8) Check the fixing condition of the upper and lower screens on the screen frame.
.9) View the tension of each drive chain and belt and the fixed condition of each shaft.
.10) View the front end of the fluttering plate; the front end of the screen box and the grain; the sealing condition of the agitated auger shell.
.11) Check the oil level and joint condition of the hydraulic system fuel tank; find that the oil leakage should be repaired in time.
2. All the conflicts of the combine harvester's smooth combine harvester require smooth, careful and correct smoothing; to improve the reliability of the machine; reduce the cost of conflict and power; to reduce the smooth time; improve the time utilization of the machine The outer spherical sealing bearing is widely used on the machine; rubber bearing; oil bearing, etc. It does not need to be smooth in the operation. Smooth operation should be carried out according to the following rules.
.1) Before smoothing, wipe the grease nipple and its surroundings.
.2) Smooth oil should be placed in a clean container; and dust and dirt should be avoided; the oil gun should also be hygienic.
.3) Always check the sealing condition of the bearing; find the oil spill emergency repair and replacement.
.4) Everything that is attached to the outside; it needs to be smooth with oil every day; it is necessary for the smooth chain to stop working in the working organization.
.5) The wooden bearing bush on the document feeder shall be immersed in the oil of 120o 130o oil temperature for two hours after the completion of the operation; then apply butter;
.6) All oil-impregnated bearings (elastic mast bushings, detachable shaft bushings) should be removed after each operation period; soak in hot oil for two hours.
.7) When the machine is inspected; the rolling bearing should be cleaned and buttered.
Ç—â”’çº5 protection protection 1, smooth. 1) smooth according to the rules.
.2) Smooth oil should be placed in a clean container; the oil gun should also be hygienic.
.3) Wipe the grease nipple, filler cap and its surroundings before filling.
.4) Always check the sealing condition of the bearing; find that the oil leakage should shorten the smooth interval.
.5) Everything attached to the chain should be smooth with oil every day. The chain should be removed (3 5 days) for oil cooking.
.6) After the completion of the harvest season; the cutting head, the dragon's finger, the wooden eye, the wooden bearing, the wooden hanger and other parts shall be removed; the oil shall be immersed in the oil of 120o-130o for 2 hours.
.7) It takes only a few drops of smooth oil to pull the joint and the lever.
.8) Check the oil level in the active axle chamber every two weeks; add smooth oil if necessary.
2, daily skill protection. 1) Before the daily work, you should arrange some residuals on the machine; unique attention should be paid to eradicate the attachment of the roller and the concave plate, the grain flutter plate, the sieve and the manure on the drafter.
.2) Check the condition of the reel (spokes, lacing, safety clutch, continuously variable transmission and its transmission organization).
.3) Check the cutter for any loss and some fixed conditions.
.4) Check the tension of the skewed chain chain.
.5) Check the fixing condition of the groove, concave plate and roller bearing.
.6) Check the fixing condition of the drafter box on the wooden bearing, and check the fixing condition of the clear grain sieve crank bearing.
.7) View the fixed condition of the stem presser.
.8) Check the tension of each pulley and chain and the fixing condition of the pulley sprocket.
.9) Check the hydraulic tank oil level (the reel and the header are in a lowered condition), and check the connection and fixing of the hydraulic joints and flanges.
.10) Check the sealing condition of the lower curtain under the header, the lower curtain of the roller inlet, and the hole cover of the threshing;
.11) Check the operational reliability of the steering gear and brakes.
.12) Finish the air filter of the air filter; check the tightness of the three wing nuts. When the dust content in the air is unique, the upper and lower filters of the air filter should be removed.
.13) Sanitary battery; vent the vent on the plug; remove the oxides on the wires and poles and check whether the joints of the wires are tight.
.14) Heat sink for sanitary radiator; view water level.
.15) Unblock the hole in the fuel tank cap; if necessary, remove the filter in the fuel filler port; release 5 kg of diesel oil and sediment to check the oil level.
.16) Check the oil level in the crankcase and fuel injection pump.
.17) Smoothed by a smooth table.
.18) Check tire pressure and fixed condition.
.19) After the daily work is completed; the grain in the grain box, the grain in the machine and the stems in the grass box should be completely removed. In the winter, the radiator and the water in the machine must be drained.
Recommend to friends comments close window Bearing related knowledge The characteristics of ceramic bearings of several common raw materials, how to choose the clearance of the rolling bearing, the sliding bearing, the bearing skill, the introduction of the bearing conflict torque, the functional requirements of the motor bearing grease
This article links to http://
Please indicate the bearing network http://
Previous:Classification analysis of bearing methods for radiators Next: Rolling bearing monitoring skills - Ferrography analysis
How to properly use and protect the wheat combine harvester
Source: China Bearing Network Time: 2018-07-20