It can cut all kinds of metal plates, pipes, and is mainly used for rapid cutting of stainless steel, carbon steel, manganese steel, galvanized sheet, various alloy plates, rare metals, etc.
Fiber Laser Cutting Machine Fiber Laser Cutting Machine,Fiber Laser Cnc Cutting Machine,Commercial Laser Cutting Machine,Ccd Camera Laser Cutting Machine Buluoer Intelligent Technology Co., Ltd. , https://www.buluoercuttingmachine.com
The daily main maintenance and maintenance are:
1. The dust and debris on the surface of the box must be removed frequently to keep the surface of Foshan Daozou clean.
2. Arrange the fasteners once a month to check if they are loose and fall off and fasten them in time.
3. Lubricant should be added to each movable connection attachment every 3 months. It is best to maintain a good lubrication condition every day.
4. After running 30,000 times, it is necessary to check the balance spring and adjust the balance in time.
5. Every 6 months, professionals should be specially inspected for wear and tear, and wear parts should be replaced.
6. The remote control battery uses DC12V, 23A battery, the service life is one year, pay attention to replace the battery, do not damp, beat, hit.
7. The remote control distance is too short. Check if the location where the host is installed is covered by metal objects or if the battery is fully charged.
Detect abnormal ring <br> <br> reasons chassis: Check the links section of the bearing and activity is abnormal Remedy: lubricate the bearings or replace <br> <br> Barrier common faults and repair methods are mainly the following:
Steps/methods
When the local coil is unable to be firmly fixed in the nest, the vibration of the car over the road surface will cause the coil in the nest to deform and change the initial inductance of the ground. At this time, the sensor must be reset before it can work normally. . The solution is to put the molten asphalt in place and fix it. [1]
The looseness of the loose screws of the barriers: the hinge screws are connected by positive and negative threads, and the upper and lower two bearings are connected by a double-headed screw. If the screws are loose, the upper and lower positions will be inaccurate. Use a 80mm long Ф4 iron rod to insert the double-headed screw to adjust the brake lever up and down in place.
If the screw is loose, the brake lever will cause the upper and lower positions of the brake lever to be inaccurate and the swing of the lever will be large. When the bolt is suspended tightly, the nut can be locked tightly.
In-position control magnets move position: Cimin Hall elements are used up and down to position. If rectangular magnets and reducer with cams change the position of the wafer, the position is inaccurate. Adjust it accurately and not flip it to solve the problem.
Power off protection switch power off: When the control part of the barrier is out of order, the automatic protection device of the barrier gate will automatically work. At this moment, the brake rod stops at the oblique position, the total power is off, and the machine does not work. At this point, the machine door is opened, and the large belt can be restored by rotating the large belt 3-8 times clockwise. If it cannot be restored to this condition many times, check whether the Hall element and the circuit board have malfunctioned.
The pull-down hook adjusts the looseness of the nut: the lower part of the chassis is provided with a pull-down hook of thread M10, and its function is to pull the spring of the balance mechanism and the zero adjustment of the balance function. It is equipped with two M10 hexagon nuts and ten spring washers. If the nut is loose, knocking noise and balance will occur when the machine is running. Even if the machine can run after the imbalance, it will greatly increase the speed reducer, motor and other transmissions. The load of the components affects the reliability and mechanical life of the operation of the barrier.
Widely used in: kitchen appliances, sheet metal chassis cabinets, mechanical equipment, electrical equipment, lighting hardware, advertising signs, auto parts, display equipment, various metal products, sheet metal cutting processing and other industries.
Principle of Fiber Laser Cutting Machine
The fiber Laser Cutting Machine adopts the international advanced fiber laser to output a high-energy density laser beam, and focuses on the surface of the workpiece, so that the area irradiated by the ultra-fine focus spot on the workpiece is instantly melted and vaporized, and the spot illumination is moved by the numerical control mechanical system. Automatic cutting is achieved. It is a high-tech equipment integrating advanced fiber laser technology, numerical control technology and precision mechanical technology.
Fiber laser Cutting Machine features
1. Can blow air to cut various metal sheets;
2. High performance, imported original packaged fiber laser, stable performance and long service life;
3. High speed, from efficiency, the speed of cutting thin plates can reach tens of meters per minute;
4. The laser is maintenance free;
5. The cutting edge has good quality, small deformation, flat appearance and beautiful appearance;
6. Adopting imported guiding transmission mechanism and servo motor, the cutting precision is high;
7. It is free to design all kinds of graphics or text for instant cutting, which is simple, flexible and convenient.
Barrier maintenance and troubleshooting
With the continuous development of the automotive industry and the ever-increasing number of automobiles, the demand for barriers is also increasing, and higher requirements have been placed on the performance of barriers. Such as gate and gate integrated movement, clutch device, intelligent anti-lift function, met resistance return device, temperature increase function (ensure use under minus 40 degrees environment), ventilation cooling system (in time to reduce motor temperature), automatic clutch device, collision avoidance A trip device. Daozha has been increasingly developed in high technology to meet the market demand for products.